In the engraving machine industry, there is a saying that seven points are used and three points are raised. Of course, few laymen know the truth. It is the so-called laymen watch the doorway and laymen watch the excitement. In fact, woodworking engraving machines, like cars, are maintained more than repaired, so that engraving machines can be used for a long time, Many users who have just come into contact with the engraving machine will have problems with the engraving machine due to illegal operation, which greatly shortens the service life of the engraving machine.

木工雕刻机如果做好维护保养工作，就可以很好地保证橱柜门雕刻机的稳定运行，加工速度和加工精度，都可以得到很好的保障;木工雕刻机布维护和保养做得好，那么前期可能修几次就修好，但是后期问题会越来越多，修好了这里那里就出问题，这是因为木工门雕刻机的一个或者几个部件损耗比较严重，就会影响到其他部件的正常工作，越是不保养，被迫损耗的部件就会越多，整台机器的运行就越容易出问题。那么橱柜门雕刻机该如何保养维护?

If the woodworking engraving machine is well maintained, it can well ensure the stable operation of the cabinet door engraving machine, and the processing speed and accuracy can be well guaranteed; If the woodworking engraving machine cloth is well maintained, it may be repaired several times in the early stage, but there will be more and more problems in the later stage. If it is repaired, there will be problems here and there. This is because one or several parts of the woodworking door engraving machine are seriously worn out, which will affect the normal work of other parts. The more maintenance is not carried out, the more parts will be forced to be worn out, The more likely the whole machine is to go wrong. So how to maintain the cabinet door engraving machine?

一、工作环境

1、 Working environment

1、保证操作间环境温度，特别注意冬季操作间温度。木工橱柜门雕刻机达到室温，少工作人员不会觉得很冷。

1. Ensure the ambient temperature of the operation room, with special attention to the temperature of the operation room in winter. When the woodworking cabinet door engraving machine reaches room temperature, at least the staff will not feel very cold.

2、查看所加油标准适用温度，少达到适宜温度。

2. Check the applicable temperature of the refueling standard and at least reach the appropriate temperature.

3、机器不用时，若室温较低倒出水箱里的水，防止冻裂水箱与水管。温度对于橱柜门雕刻机的影响不是很大，但由于很多客户给丝杠加黄油，冬季也忘了清理，导致每次开机运行不开，有的工作室气温很低，虽然加了机油，可还是冻上了，机器运行不起来。

3. When the machine is not in use, if the room temperature is low, pour out the water in the water tank to prevent freezing crack of the water tank and water pipe. The temperature does not have a great impact on the cabinet door engraving machine, but because many customers add butter to the lead screw and forget to clean it in winter, they can't start up and run every time. The temperature in some studios is very low. Although the oil is added, it is still frozen and the machine can't run.

4.操作间的湿度不能太大，否则机器的电器配件很容易损耗

4. The humidity in the operation room should not be too high, otherwise the electrical accessories of the machine are easy to be worn out

5.操作间的电磁干扰一定要注意，干扰太大的话很容易使的橱柜门雕刻机的加工精度受影响

5. Pay attention to the electromagnetic interference in the operation room. If the interference is too large, it is easy to affect the machining accuracy of the cabinet door engraving machine

二、定时清洁

2、 Regular cleaning

木工雕刻机使用完毕之后，一定要注意清理台面和裸露在外的电器配件上的粉尘、木屑等，包括机器的导轨和滑块，包括机器的丝杠和主轴电机。包括机器的工控箱，特别是工控箱里粉尘稍多就会导致电路板的运行处问题，很容易出现断点，乱跑等情况。

After the woodworking engraving machine is used, be sure to clean the dust and sawdust on the table and exposed electrical accessories, including the guide rail and sliding block of the machine, including the lead screw and spindle motor of the machine. Including the industrial control box of the machine, especially a little more dust in the industrial control box will lead to problems in the operation of the circuit board, which is prone to breakpoints, random running and so on.

三、定期检查

3、 Regular inspection

大部分木工雕刻机都是使用电脑来操作，而电脑一旦出问题的话整台木工雕刻机就没办法用了，所以维护好电脑也是很重要。电脑维护注意一下以下几个方面。

Most woodworking engraving machines are operated by computers, and once the computer goes wrong, the whole woodworking engraving machine can't be used, so it's also very important to maintain the computer. Pay attention to the following aspects in computer maintenance.

1、定期清理机箱灰尘，用空气喷枪与小毛刷定期清理、小心灰尘过多引起工控卡出。注意机箱的散热装置，特别是夏天，小心控制线温度过高烧坏电路板等设备。

1. Clean the dust of the chassis regularly, and clean it regularly with air spray gun and small brush. Be careful that too much dust will cause the industrial control card to come out. Pay attention to the heat dissipation device of the chassis, especially in summer. Be careful to control that the wire temperature is too high and burn the circuit board and other equipment.

2、定期清理电脑垃圾、整理磁盘碎片，优化电脑系统，保持电脑系统的稳定性。

2. Regularly clean up computer garbage, sort out disk fragments, optimize the computer system and maintain the stability of the computer system.

3、定期查杀电脑，但注意工作时不可以打开防毒程度，小心干扰

3. Check and kill the computer regularly, but pay attention not to open the anti-virus level during work and be careful of interference