联系我们
18560023440
王经理：18560023440
地址：山东省德州市齐河县经济开发区齐众大道7号-2车间
新闻资讯
玉石雕刻机台面不平，主轴发出噪音如何处理？
来源：http://www.jmycnc.com 时间：2021-05-07
玉石雕刻机台面不平，是不能完成浴室的雕刻的，所以在购买设备时一定要注意这一问题，面对玉石雕刻机主轴发出噪音这个问题，要分清楚噪音，然后选择具体的方法作出解决。下面就由小编来给大家详细介绍一下玉石雕刻机台面不平，主轴发出噪音如何处理？
Jade carving machine table is uneven, can not complete the bathroom carving, so in the purchase of equipment must pay attention to this problem, in the face of jade carving machine spindle noise this problem, we must first distinguish the noise, and then choose a specific method to solve. The following is a detailed introduction of jade carving machine by Xiaobian. How to deal with the noise from the spindle?
一、玉石雕刻机台面不平怎么办?
1、 Jade carving machine table uneven how to do?
1、玉石雕刻机如果是台面不平的话，那么只能找厂家解决了雕刻机台面是平的但是垫板不平了要么更换垫板，要么把垫板铣平。雕刻机台面不平怎么预防呢?雕刻机运行的时候，直接把刀具定在雕刻机台面上，这样可以保证刀始终下到台面上，不损坏台面。
1. If the table of jade carving machine is uneven, we can only find the manufacturer to solve the problem that the table of carving machine is flat, but the base plate is uneven. Either replace the base plate or mill the base plate flat. How to prevent uneven surface of engraving machine? When the engraving machine is running, the cutter is directly fixed on the table of the engraving machine, which can ensure that the cutter is always on the table without damaging the table.
2、具体的操作方式是计算路径的时候，不要根据资料的厚度来设置“雕刻深度”而是直接设置为“0mm生产G代码文件前，可以将“抬刀深度”设置为：抬刀高度+切割资料厚度。
2. When calculating the path, do not set the "engraving depth" according to the thickness of the data, but directly set it to "0 mm". Before producing the G code file, you can set the "tool lifting depth" to: tool lifting height + cutting data thickness.
3、举个例子，刀具定在资料外表抬刀高度8mm加工的资料厚度为10mm那么“抬刀距离”值就为：8+10=18mm剩下的除了把刀具定在雕刻机台面上外，其他操作也是不变的。
3. For example, if the tool is set on the surface of the data, the tool lifting height is 8mm and the data thickness is 10mm, then the value of "tool lifting distance" is 8 + 10 = 18mm. The rest of the operations are the same except that the tool is set on the table of the engraving machine.
二、玉石雕刻机主轴发出噪音如何处理？
2、 How to deal with the noise from the main shaft of jade carving machine?
1、杂质音
1. Impurity tone
由轴承或的清洁度引起，发出一种不规则的异常音，声音时有时无，时大时小，在高速电机上发生频繁。
It is caused by the bearing or overall cleanliness, which makes a kind of irregular abnormal sound, sometimes not, sometimes large and sometimes small, which occurs frequently in high-speed motor.
解决方法：选用好的油脂、提高注脂前的清洁度、加强轴承的密封性能、提高安装环境的清洁度
Solutions: select good grease, improve the cleanliness before grease injection, strengthen the sealing performance of bearing, and improve the cleanliness of installation environment
2、淅沥淅沥的声音
2. The sound of pattering
由保持器与滚动体振动、冲撞产生，不管润滑脂种类如何都可能产生，承受力矩、负荷或径向游隙大的时候更容易产生。
It is caused by the vibration and collision between the retainer and the rolling element, regardless of the type of grease. It is more likely to occur when the torque, load or radial clearance is large.
解决方法：提高保持器精度、选用游隙小的轴承或对轴承施加预负荷、降低力矩负荷，减少安装误差、选用好的油脂。
Solutions: improve the accuracy of retainer, select bearings with small clearance or apply preload to bearings, reduce torque load, reduce installation error and select good grease.
3、嗡嗡的声音
3. A buzzing sound
马达无负荷运转是发出类似蜂鸣一样的声音，且马达发生轴向异常振动，开或关机时有嗡嗡声。
When the motor runs without load, it makes a sound similar to a beep, and the motor has abnormal axial vibration, and there is a buzzing sound when it is turned on or off.
解决方法：多出现在润滑状态不好，以及在冬天且两端用球轴承的马达，主要是轴调心性能不好时，轴向振动影响下产生的一种不稳定的振动。
Solution: it often occurs in the motor with poor lubrication and ball bearings at both ends in winter, which is mainly an unstable vibration under the influence of axial vibration when the shaft alignment performance is poor.
4、哒哒的声音
4. The sound of dada
声音频率随轴承转速而变化，零件表面波纹度是引起噪音的主要原因。
The sound frequency varies with the bearing speed, and the surface waviness of the parts is the main cause of the noise.
解决方法：改善轴承滚道表面加工质量，降低波纹度幅值、减少碰伤、修正游隙预紧力和配合，检查自由端轴承的运转，改善轴与轴承座的精度安装方法。
Solutions: improve the surface processing quality of the bearing raceway, reduce the amplitude of waviness, reduce the impact, correct the clearance preload and fit, check the operation of the free end bearing, and improve the precision installation method of the shaft and bearing seat.
以上就是小编给大家介绍的玉石雕刻机台面不平，主轴发出噪音如何处理？希望小编的总结能帮到大家。有问题可以在网站http://www.jmycnc.com下方留言咨询哦。
The above is the jade carving machine table is uneven, how to deal with the noise of the spindle? I hope the summary of Xiaobian can help you. Questions can be found on the website http://www.jmycnc.com Below message consultation oh.
- 上一篇：石材雕刻机的常用雕刻方法汇总
- 下一篇：木工雕刻机丢步是什么原因
