Generally, the price of engraving machine depends on the configuration of engraving machine and the size of machine tool. But still need from the following aspects to choose their own engraving machine.

驱动动系统：目前雕刻机驱动系统主要分步进系统和系统两大类，步进系统占着主导地位这要原因经济实惠能满足一般客户的使用要求，步进系统属于半闭环系统精度以步距角计算，系统完全属于封闭环模式内有测量反馈系统所以精度比较高，动力大、运行平稳、要求较高的客户可选择驱动系统的机器（稍贵）。

Driving system: at present, the driving system of engraving machine is mainly divided into two categories: step-by-step system and system, and the stepping system is dominant. This is because it is economical and can meet the requirements of general customers. The stepping system belongs to a semi closed-loop system, and its accuracy is calculated by the step angle. The system is completely in the closed-loop mode, and there is a measurement feedback system, so the precision is relatively high, the power is large, and the operation is stable Customers with higher requirements can choose to drive the machine (the price is slightly higher).

目前市场上也出现了半系统，是改进版的步进系统，请客户选机器时注意。(分国产和进口)控制系统：目前以维宏、DSP操作系统、mach3为主导少部分，进口台湾宝元和新代控制系统。作图软件：一般使用、文泰、精雕、TYPE3、artcam。

At present, there is a Semi-system in the market, which is an improved version of the step-by-step system. Please pay attention when selecting the machine. (domestic and imported) control system: at present, Weihong, DSP operating system and Mach3 are the leading parts, while Taiwan Baoyuan and new generation control system are imported. Drawing software: general use, Wentai, Jingdiao, type3, ArtCAM.

雕刻机传动方式：目前雕刻机分三种传动方式，丝杠传动、齿条传动和同步带传动。

Engraving machine transmission mode: at present, engraving machine is divided into three transmission modes, screw drive, rack drive and synchronous belt drive.

丝杠机优缺点：丝杠传动是雕刻机起源时的传动方式，特点精度高，运行速度慢，环境要求较高，使用寿命相对较短，Y轴单丝杠不易太长（机型不能太大），高速运行时容易抖动，如果安装精度不高Y轴丝杠长时间运行将有被甩断的可能。

Advantages and disadvantages of lead screw machine: screw drive is the transmission mode of engraving machine origin, with high precision, slow running speed, high environmental requirements, relatively short service life, Y-axis horizontal screw is not easy to be too long (the model can not be too large), and it is easy to shake when running at high speed. If the installation accuracy is not high, the y-axis lead screw may be broken if it runs for a long time.

如果要求精度过高的可以Ｙ轴双丝杠结构来满足要求，一般加工速度７米左右。（主要适用广告、木制品、小工艺品、较轻石材根据刀具不同可加工任意雕刻材料）

If the required accuracy is too high, Y-axis double lead screw structure can meet the requirements, and the general processing speed is about 7 meters. (mainly suitable for advertising, wood products, small handicrafts and light stone. It can process any carving material according to different cutting tools)

齿条机优缺点：齿条机是既丝杠机的升级版，介于丝杠机无法满足高速度加工的要求而新开发的机型，速度快、环境要求不苛刻相对使用寿命长、精度相对丝杠机低一些，齿条机Ｙ轴Ｘ轴为齿轮齿条传动、Ｚ轴一般为丝杠传动，精度要求主要根据导轨和齿轮齿条的啮合精度来决定。机器尺寸长度可以够大，维护方便一般配备手动注油系统，建议加工速度可达15米左右。

Advantages and disadvantages of rack machine: rack machine is an upgraded version of lead screw machine, which can not meet the requirements of high-speed processing. However, the newly developed machine has the advantages of fast speed, low environmental requirements, long service life and low precision compared with the lead screw machine. The Y-axis and x-axis of the rack machine are driven by the rack and pinion, and the z-axis is generally driven by the lead screw. The accuracy requirements are mainly based on the guide rail and gear rack Meshing accuracy. The size and length of the machine can be large enough and easy to maintain. Generally, it is equipped with manual oiling system, and the processing speed is recommended to be about 15m.

同步带传动：同步带传动主要用于激光雕刻机及等离子切割，质量轻、精度高、好维护、时间久容易松弛影响加工精度等特点。（激光机主要使用于广告业、工艺品雕刻、布匹，皮革、玻璃、石材、水晶等一些非金属材料的影雕线雕等也可在少数金属材料上加工、区间和激光管的功率有关

Synchronous belt drive: synchronous belt drive is mainly used for laser engraving machine and plasma cutting. It has the characteristics of light weight, high precision, good maintenance, long time and easy relaxation, which affects the processing accuracy. (laser machines are mainly used in advertising, arts and crafts carving, cloth, leather, glass, stone, crystal and other non-metallic materials for shadow carving, line carving, etc., and can also be processed on a few metal materials. The price range is related to the power of the laser tube
关键词：保丽龙雕刻机