联系我们
18560023440
王经理：18560023440
地址：山东省德州市齐河县经济开发区齐众大道7号-2车间
业内资讯
四轴保丽龙雕刻机如何进行保养维护？
来源：http://www.jmycnc.com 时间：2020-10-01
本文的內容将再次为大伙儿叙述相关四轴保丽龙雕刻机设备维护管理的相关流程，接下去一起访问文章内容，掌握相关内容！
The content of this article will once again narrate the relevant four axis styrofoam engraving machine equipment maintenance and management process, and then visit the article content together to master the relevant content!
1.定时执行清理电源电路箱的排热排风系统，请定期维护电气控制柜上的每个风扇工作是不是一切正常，按时用吸尘机一次电气控制柜里的尘土，查验接线端子排螺钉是不是松脱，以确保电源电路一切正常、靠谱应用。
1. Regularly clean the heat exhaust system of the power circuit box. Please regularly maintain whether all fans on the electrical control cabinet are working normally. Clean the dust in the electrical control cabinet with a vacuum cleaner on time, and check whether the screw of the terminal block is loose, so as to ensure the normal and reliable application of the power supply circuit.
2.应尽量避免开电气控制柜的门，严禁开关门工作中，在手工雕刻时空气中一般都是有尘土、木渣或金属粉，一旦他们落在电气控制柜内的线路板或电子元器件上，非常容易造成电子器件间接地电阻降低，乃造成 电子器件及线路板毁坏。
2. The door of electrical control cabinet should be avoided as far as possible. It is strictly forbidden to open or close the door. Dust, wood slag or metal powder are usually found in the air during manual carving. Once they fall on the circuit board or electronic components in the electrical control cabinet, it is very easy to reduce the indirect resistance of electronic devices and even cause damage to electronic devices and circuit boards.
3.定期维护设备各构件螺丝是不是松脱。
3. Regularly maintain whether the screw of each component of the equipment is loose.
4.机械泵的维护保养：
4. Maintenance of mechanical pump:
A水循环系统打气泵呼吸口腔内部的金属丝网制品是用于避免 外地人细颗粒物进到泵壳，此过滤网应随时随地保持干净，防止阻塞而造成泵的泵效降低，当离心水泵无需时应当每几日接电源运行数分钟，避免 泵身长锈没法一切正常运行。
The metal mesh products inside the breathing mouth of the air pump of a water circulation system are used to prevent the foreign people from entering the pump shell. The filter screen should be kept clean at any time and place to prevent the pump efficiency from being reduced due to blockage. When the centrifugal pump is not needed, it should be connected to the power supply for several minutes every few days to avoid the pump body from being rusty and unable to operate normally.
B一般机械泵也应当松掉蝶形螺母，取下纸质过滤芯按时用髙压汽体滤网，发觉过滤芯换气不如意或毁坏，应立即拆换，依据使用时间长度能用髙压加油枪给各处滚动轴承上油。
B General mechanical pump should also loosen the butterfly nut, remove the paper filter element, and remove the filter screen with high pressure steam on time. If it is found that the air exchange of the filter element is unsatisfactory or damaged, it should be removed and replaced immediately. According to the service time, the high pressure oil gun can be used to oil the rolling bearings everywhere.
5.严苛依照使用说明书实际操作及遵循应用标准。
5. Strictly follow the instruction manual and follow the application standard.
以上内容就是为大伙儿详细介绍的相关四轴保丽龙雕刻机维护保养的流程相关内容，雕刻机与人一样也是有性命的，要想雕刻机各构件自始终保持稳定的情况，坚持不懈常常的维修保养是十分关键的。那样能够把许多常见故障隐患解决在萌芽期情况，避免 特发常见故障产生。实际操作工作人员应当培养常常对应用机器设备开展维护保养的良好的习惯！
The above content is a detailed introduction to the maintenance process of the relevant four axis styrofoam engraving machine. The engraving machine has life as well as people. If you want to keep the components of the engraving machine stable from beginning to end, it is very important to keep constant maintenance. In this way, many common faults can be solved in the bud, and the occurrence of special common faults can be avoided. The actual operation staff should cultivate the good habit of carrying out the maintenance of the applied machinery and equipment frequently!
关键词：保丽龙雕刻机
关键词：保丽龙雕刻机
