联系我们
18560023440
王经理：18560023440
地址：山东省德州市齐河县经济开发区齐众大道7号-2车间
新闻资讯
有关雕刻机雕刻不够圆润的原因
来源：http://www.jmycnc.com 时间：2022-03-17
在实际的生产过程中，雕刻机雕刻的效果不一定能满足客户的要求，特别是如果效果不够流畅，我们应该找出原因并及时处理。但在实际工作中,如果出现这种情况,主要有以下两个原因:
In the actual production process, the engraving effect of the engraving machine may not meet the requirements of customers, especially if the effect is not smooth enough, we should find out the reason and deal with it in time. However, in practice, if this happens, there are two main reasons:
1、雕刻机的y轴或x轴可能同时有间隙，导致雕刻过程中抖动，雕刻路径偏差，雕刻不顺畅;
1. The y-axis or x-axis of the engraving machine may have a gap at the same time, resulting in jitter in the engraving process, deviation of engraving path and unsmooth engraving;
解决方案：改变直线或曲线的速度，改变数值由雕刻机本身的参数决定。
Solution: change the speed of straight line or curve, and the change value is determined by the parameters of the engraving machine itself.
2、雕刻机的线速度与曲线速度相差过大，导致雕刻机在走曲线时产生振动，这意味着雕刻路径偏离，雕刻不平滑。
2. The difference between the linear speed of the engraving machine and the curve speed is too large, resulting in the vibration of the engraving machine when walking the curve, which means that the engraving path deviates and the engraving is not smooth.
解决方法：如果雕刻机是一个圆形导轨，找到一种方法来改变导轨或滑块，动作会比较大，这取决于原因。如果它是一个正方形的轨道，它就简单多了。只需调整上下滑块或前后滑块;
Solution: if the engraving machine is a circular guide rail, find a way to change the guide rail or slider, the action will be relatively large, depending on the reason. If it were a square orbit, it would be much simpler. Just adjust the upper and lower sliders or the front and rear sliders;
在使用过程中，济南雕刻机出现雕刻不圆滑的现象是非常常见的，这就需要相关操作人员及时检查原因，对症下药，解决问题，具体方法可以参考上述建议。如果还是无法解决问题，那就需要联系厂家或者找维修人员进行检修，不要盲目维修，以免对雕刻机造成二次伤害。
In the process of use, it is very common that the engraving of Jinan engraving machine is not smooth, which requires relevant operators to check the causes in time, suit the remedy to the case and solve the problems. For specific methods, please refer to the above suggestions. If you still can't solve the problem, you need to contact the manufacturer or find maintenance personnel for maintenance. Don't repair blindly to avoid secondary damage to the engraving machine.
以上就是为大家介绍的有关3050雕刻机的详细介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.jmycnc.com
The above is the detailed introduction of 3050 engraving machine. I hope it will help you If you have any questions, please contact us We will provide you with professional service http://www.jmycnc.com//
- 上一篇：木工开料机生产过程中灰尘如何有效解决？
- 下一篇：开料机能提率的可行性方法有哪些？
