雕刻机的日常保养维护

来源：http://www.jmycnc.com 时间：2021-08-16 

1.开机前检查各部件是否在正常位置，各运动部件是否完好，导轨有油润滑，然后开机底速动转1~2分钟，观察是否有异常情况，等机床运转正常后方能进行工作；

1. Before starting the machine, first check whether all parts are in the normal position, whether all moving parts are in good condition, and the guide rail is lubricated with oil. Then start the machine at the bottom and rotate it for 1 ~ 2 minutes to observe whether there are abnormal conditions. The machine can work only after the machine runs normally; 

2.工情况选择刀具、转速、进刀量、加工速度及顺，逆铣方向；

2. Select the tool, rotating speed, feed rate, processing speed and forward and reverse milling direction according to the working conditions;

3.整个加工过程不能用手或碎布等杂物接触正在转动的刀具，在清理石粉时要确保刀具完全停止运转才能；

3. During the whole processing process, do not touch the rotating tool with hands or rags. When cleaning stone powder, ensure that the tool stops completely before removal;

4.作业完毕，关闭电源，各部位石粉，杂物。其他相关辅助工具必 须放还原处；

4. After the operation, turn off the power supply and remove the stone powder and sundries at all parts. Other relevant auxiliary tools must be placed at the restoration place;

5.定期（依使用情况）清理电器箱内灰尘，检查接线端子螺丝是否松动，以保证机器电路安 全，可靠使用；

5. Clean the dust in the electrical box regularly (according to the use situation) and check whether the screw of the wiring terminal is loose, so as to ensure the safe and reliable use of the machine circuit;

6.工作台面及导轨每天擦拭干净，不可有石粉、油污杂质等；

6. The worktable and guide rail shall be wiped clean every day without stone powder, oil stain and impurities;

7.连续运行要保证冷却水的洁净及冷却机的正常工作，不可以使水冷主轴电机出现缺水现象，定时更换冷却水，以防止水温过高；

7. For continuous operation, ensure the cleanness of cooling water and the normal operation of the cooler. Do not make the water-cooled spindle motor lack water. Replace the cooling water regularly to prevent the water temperature from being too high;

8.定期依使用情况）检查机器各部件螺钉是否松动，以保证机器可靠；

8. Regularly check whether the screws of all parts of the machine are loose (according to the use conditions) to ensure the reliability of the machine;

9.每次机器使用完毕，要注意清理，务必将平台及传动系统上的粉尘清理干净，定期（每周）对传动系统（X,Y,Z,A,C等轴）润滑加油；

9. Pay attention to cleaning every time the machine is used. Be sure to clean the dust on the platform and transmission system, and lubricate and refuel the transmission system (x, y, Z, a, C and other shafts) regularly (weekly);

10.机器若长时间不使用，应定期（每周）加油空走，以保证传动系统的灵活性；

10. If the machine is not used for a long time, it shall be refueled and idled regularly (weekly) to ensure the flexibility of the transmission system;

11.主轴、工作台和导轨面严禁敲打和冲击，工作台及道轨面不得乱放工具和毛坯及不相关的工件或物品；

11. It is forbidden to knock and impact the spindle, workbench and guide rail surface, and tools, blanks and irrelevant workpieces or articles shall not be placed on the workbench and track surface;

• 上一篇：石材雕刻机发热的原因有哪些？
• 下一篇：模具雕刻机的精度要求会更高一些

相关产品：
• 
  木工雕刻机
• 
  1325木工雕刻机独...
• 
  1325木工雕刻机
• 
  1325木工镂空花格...
• 
  1225型平雕圆雕一...

相关新闻：
• 
  激光雕刻机和机械雕刻...
• 
  三轴雕刻机无心外圆磨...
• 
  石材雕刻机断刀的原...
• 
  数控开料机会受到什么...
• 
  泡沫雕刻机日常井盖如...