在使用雕刻机的时候，须知一定的安 全知识，而且可能由于操作不当或者维护不当导致一些新问题产生，那么改如何检验泡沫雕刻机机箱呢?要知道检验泡沫雕刻机机箱可预防一定的问题出现，提高泡沫雕刻机的使用寿命.下面一起去看看吧.

When we use the engraving machine, we need to know certain safety knowledge, and may cause some new problems due to improper operation or improper maintenance. Then how do we test the foam carving machine case? We should know that testing the foam engraving machine box can prevent certain problems and improve the service life of the foam engraving machine.

1.机箱里的电缆线不允许有凌乱的现象.

1. The cables in the case are not allowed to be messy

2.机箱的线号要整齐，线号一定齐全(各线端头处都应有相应的线号);线是否压好，有没有铜丝露在外面.

2. The wire number of the chassis should be neat and complete (there should be corresponding wire number at the end of each wire); Whether the wire is well pressed and whether the copper wire is exposed

3.机箱标识是否贴全、贴正;各个部分是否已打扫干净;保证没有杂物，金属屑等杂物.

3. Whether the chassis identification is fully and correctly pasted; Whether all parts have been cleaned up; Make sure there are no sundries, metal scraps, etc

4.变压器﹑变频器﹑驱动器的接触器的是否留有余量，这些地方的线不宜太紧，否则会影响线的使用寿命，数控保丽龙雕刻机厂家，线可以弯90°的弧度，在床身下面安装的变频器进线和出线分别要用缠绕管缠绕，在床身上打孔穿线时一定加护套.

4. Whether the contactor of transformer, frequency converter and driver has allowance, the wire in these places should not be too tight, otherwise it will affect the service life of the wire. For CNC styrofoam engraving machine manufacturers, the wire can be bent for 90 ° The inlet and outlet of frequency converter installed under the bed should be wound with winding pipe respectively, and the sheath must be added when drilling holes on the bed

5.维宏、DSP系统等进机箱的数据线是否固定好(可用管卡固定)，否则会数据线插头插针拉坏;DSP/维宏系统的数据线是否用卡子固定;有3.0KW以上的变压器底面一定加加厚平垫背母，是否加了.

5. Whether the data cable of Weihong and DSP system into the chassis is fixed (it can be fixed with pipe clamp), otherwise the plug pin of the data cable will be damaged; Whether the data line of DSP / macro system is fixed with clip; If there is a transformer above 3.0kw, the bottom surface must be thickened

6.机箱的开关一般固定在机箱的顶部，开关线一定用缠绕管缠好，大型保丽龙雕刻机厂家，不能有凌乱现象;面板周围是否有胶影响机箱的外观.

6. The switch of the case is generally fixed on the top of the case, and the switch wire must be wrapped with winding tube. Large styrofoam engraving machine manufacturers should not be messy; Whether there is glue around the panel affects the appearance of the chassis

雕刻机的应用范围及日常维护保养雕刻从加工原理上讲是一种钻铣组合加工，雕刻机多种数据输入模式根据需要游刃有余。因为雕刻机的应用范围非常广泛，因此有必要了解各种雕刻机的的应用范围。小功率的只适合做双色板、建筑模型、小型标牌、三维工艺品等。由于功率太小而大大影响了其应用的范围。大功率雕刻机可以做小功率雕刻机的东西。适合做大型切割、浮雕、雕刻。

Engraving machine application scope and daily maintenance engraving from the processing principle is a combination of drilling and milling processing, engraving machine a variety of data input mode according to the need. Because the application range of engraving machine is very wide, it is necessary to understand the application range of various engraving machines. Low power is only suitable for two-color boards, building models, small signs, three-dimensional crafts, etc. Because the power is too small, its application range is greatly affected. High power engraving machine can be used for small power engraving machine. Suitable for large cutting, relief and carving.