联系我们
18560023440
王经理：18560023440
地址：山东省德州市齐河县经济开发区齐众大道7号-2车间
业内资讯
石材雕刻刀坏的原因有一下几点?
来源：http://www.jmycnc.com 时间：2021-04-25
有时接到客户电话,说刀具怎么一老断,而且还非常严重,其实这跟石材雕刻机的使用,石材雕刻刀,还有石材的工艺认识不足的原因.可以在使用中累计经验,什么石材用什么刀具,用什么样的给进速度,而且还和编程人员的路径也有关系.简单来来说下石材雕刻刀坏的原因有一下几点.
Sometimes I get a call from a customer, saying that the cutting tool is broken, and it's very serious. In fact, this is due to the use of stone carving machine, stone carving knife, and the lack of understanding of stone technology. I can accumulate experience in the use, what kind of stone, what kind of cutting tool, what kind of feeding speed, In short, there are several reasons for the broken stone carving knife
1、雕刻机本身机器原因，Z轴速度太快，容易断刀，刀夹变形容易断刀。选主轴功率，石材雕刻机一般3000W就可以了，加工速度可以保证，又能较为省电；在石材雕刻机技术尚不成熟的阶段选择一款质量较好的石材雕刻刀是你必须要考虑的。
1. Engraving machine itself machine reason, z-axis speed is too fast, easy to break the knife, knife clip deformation easy to break the knife. Choose the spindle power, stone carving machine generally 3000W can be, processing speed can be guaranteed, and can save electricity; In the stone carving machine technology is not mature stage, choose a better quality stone carving knife is you must consider.
2、材料不符合，金刚石适合雕刻大理石，但是不可能所有的版画书法都可以雕刻。金刚石适合质地细腻的硬质石材。刀具的使用寿命与走刀的速度关系很大，越硬的石材走刀速度要求越慢
2. Materials do not match, diamond is suitable for carving marble, but not all of the engraving calligraphy can be carved. Diamond is suitable for hard stone with fine texture. The service life of the cutting tool is closely related to the cutting speed. The harder the stone is, the slower the cutting speed is required
3、雕刻石材的工作环境有水，没水降温,余热就很容易断.刀尖与石材接触部位要有充足的循要有充足的水分。
3. If there is water in the working environment of carving stone, if there is no water to cool down, the waste heat will be easily broken. There should be sufficient circulation and water in the contact part between the knife tip and stone.
4、在编程时要保证每次下刀时都要柔性进给；对操作者的要求：在编程时要保证每次下刀时都要柔性进给。刀尖部位要旋转时接触物体。
4. In programming, flexible feeding should be ensured every time cutting; Requirements for the operator: when programming, it is necessary to ensure that flexible feed is required every time when cutting. Contact the object when the tip of the knife needs to rotate.
以上就是石材雕刻刀具容易断的原因,经验都是慢慢累积起来的.新手可以没断次到分析下原因,然后记录下来,时间长了就非常有经验了.
The above is the reason why stone carving tools are easy to break. Experience is accumulated gradually. Novices can analyze the reasons without breaking times, and then record them. After a long time, they will be very experienced
- 上一篇：保丽龙雕刻机的速度慢是什么原因？
- 下一篇：如何选择质量过硬的开料机？
