联系我们
18560023440
王经理：18560023440
地址：山东省德州市齐河县经济开发区齐众大道7号-2车间
业内资讯
日常我们该如何保养雕刻机？
来源：http://www.jmycnc.com 时间：2021-04-12
1.开机前检查各部件是否在正常位置，各运动部件是否完好，导轨有油润滑，然后开机底速动转1~2分钟，观察是否有异常情况，等机床运转正常后方能进行工作；
1. Before starting the machine, first check whether the parts are in normal position, whether the moving parts are in good condition, and whether the guide rail is lubricated with oil. Then start the machine and rotate it at the bottom for 1 ~ 2 minutes to observe whether there is any abnormal situation, and wait for the machine to work normally;
2.工情况选择刀具、转速、进刀量、加工速度及顺，逆铣方向；
2. Select the tool, speed, feed, processing speed and the direction of forward and reverse milling according to the working conditions;
3.整个加工过程不能用手或碎布等杂物接触正在转动的刀具，在清理石粉时要确保刀具完全停止运转才能；
3. During the whole machining process, it is not allowed to use hands or rags and other debris to contact the rotating cutting tool. When cleaning the stone powder, it is necessary to ensure that the cutting tool stops completely;
4.作业完毕，关闭电源，各部位石粉，杂物。其他相关辅助工具必须放还原处；
4. After the operation, turn off the power and remove the stone powder and debris. Other relevant auxiliary tools must be put in the reduction place;
5.定期（依使用情况）清理电器箱内灰尘，检查接线端子螺丝是否松动，以保证机器电路，可靠使用；
5. Clean up the dust in the electrical box regularly (according to the use situation), and check whether the terminal screw is loose, so as to ensure the safe and reliable use of the machine circuit;
6.工作台面及导轨每天擦拭干净，不可有石粉、油污杂质等；
6. Clean the worktable and guide rail every day without stone powder, oil, impurities, etc;
7.连续运行要保证冷却水的洁净及冷却机的正常工作，绝不可以使水冷主轴电机出现缺水现象，定时更换冷却水，以防止水温过高；
7. The continuous operation should ensure the clean cooling water and the normal operation of the cooler. The water-cooled spindle motor must not be short of water. The cooling water should be replaced regularly to prevent the water temperature from being too high;
8.定期依使用情况）检查机器各部件螺钉是否松动，以保证机器可靠；
8. Regularly check whether the screws of all parts of the machine are loose to ensure the reliability of the machine;
9.每次机器使用完毕，要注意清理，务必将平台及传动系统上的粉尘清理干净，定期（每周）对传动系统（X,Y,Z,A,C等轴）润滑加油；
9. Pay attention to clean up the dust on the platform and transmission system after each use of the machine, and lubricate the transmission system (x, y, Z, a, C, etc.) regularly (weekly);
10.机器若长时间不使用，应定期（每周）加油空走，以保证传动系统的灵活性；
10. If the machine is not used for a long time, it should be refueled regularly (weekly) to ensure the flexibility of the transmission system;
11.主轴、工作台和导轨面严禁敲打和冲击，工作台及道轨面不得乱放工具和毛坯及不相关的工件或物品；
11. It is strictly forbidden to knock and impact the spindle, worktable and rail surface, and tools, blanks and irrelevant workpieces or articles shall not be placed on the worktable and rail surface;
以上就是小编为大家介绍保丽龙雕刻机的相关内容，希望可以帮助到大家，更多精彩内容请大家直接关注：http://www.jmycnc.com
The above is Xiaobian's introduction to the relevant content of styrofoam engraving machine. I hope it can help you. For more wonderful content, please pay attention to: http://www.jmycnc.com
- 上一篇：木工雕刻机如何操作不伤台面？
- 下一篇：石材雕刻机可用于哪些材料的雕刻工作呢？
