雕刻机以其快速的雕刻效率，熟练的雕刻工艺，很快赢得了众多客户的青睐，随着大量的保丽龙雕刻机充实到市场，由于缺乏正确的操作人员，客户往往在使用过程中碰到一些小问题不知如何解决。墨渊作为雕刻机的供应商来为大家介绍一下雕刻机的主轴水冷堵死该如何进行解决：
Engraving machine with its rapid carving efficiency, skilled carving technology, quickly won the favor of many customers, with a large number of styrofoam engraving machines to the market, due to the lack of correct operators, customers often encounter some small problems in the use process, do not know how to solve them. As the supplier of engraving machine, Moyuan introduces how to solve the problem of water-cooling blocking of the main shaft of engraving machine
雕刻机主轴水冷堵死不通水，主要是因为雕刻机主轴的水路堵塞造成的，可以先暂停设备的运行，然后使用气枪反复疏通循环冷却水路，疏通完毕之后，更换雕刻机主轴冷水机的循环冷却水（纯净水或者蒸馏水），防止水垢生成的同时过滤水中杂质，确保主轴冷水机的水质干净，提升冷水机的制冷效果。


The main reason for the water blocking of the main shaft of the engraving machine is that the water channel of the main shaft of the engraving machine is blocked. The operation of the equipment can be suspended first, and then the circulating cooling water of the main shaft water cooler of the engraving machine can be dredged repeatedly by using an air gun. After dredging, the circulating cooling water (pure water or distilled water) of the main shaft water cooler of the engraving machine shall be replaced to prevent scale formation and filter impurities in the water to ensure the main shaft cold water The water quality of the chiller is clean, which improves the refrigeration effect of the chiller.
由于雕刻机加工特性，现在目前大部分雕刻主轴都是选用的水冷主轴，而水冷主轴就需要使用水循环进行降温处理，并保证在雕刻过程中水循环不能中断。很多客户在主轴水循环不太注意，很容易会导致主轴水循环不好，或者主轴水循环堵塞现象。要想避免这样的问题发生，客户只要做好以下几点即可。
Due to the processing characteristics of engraving machine, at present, most carving spindles are water-cooled, and the water-cooled spindle needs to use water circulation for cooling treatment, and ensure that the water circulation can not be interrupted in the engraving process. Many customers do not pay attention to the water circulation of the main shaft, which can easily lead to poor water circulation of the main shaft or blockage of the water circulation of the main shaft. To avoid such problems, customers need to do the following.
一、保证水质的干净，不能有任何杂质，以防阻塞电机的进水口；
1、 Ensure that the water quality is clean and free of any impurities to prevent blocking the water inlet of the motor;
二、水泵功率一定不能太小，否则由于主轴和水泵有高低落差，而不能很好的进行水循环；
2、 Pump power must not be too small, otherwise because of the spindle and pump have high and low drop, and can not be very good water circulation;
三、注意经常更换或添加纯净水，以免水循环时间过长，水温过高，在主轴水循环管道内产生水垢；
3、 Pay attention to replace or add pure water frequently, so as to avoid scaling in the main shaft water circulation pipe due to too long water circulation time and too high water temperature;
只要注意好以上三点就可以很好的避免雕刻主轴堵塞或者水循环冷却效果差的问题，
As long as you pay attention to the above three points, you can avoid the problems of blocking the carving spindle or poor cooling effect of water circulation,