开料机系统显示重启系统并做回零操作怎么办 。
How to restart the system and return to zero operation.
，操作者必须要对数控开料机非常熟悉，不论是说开料机的结构、应用范围还是说开料机的技术规范以及使用时必须遵守的守则，都必须做到了熟于心，以免在使用时发生意外。另外在进行正式的操作之前，一般都要求操作者进行考试，只有考试合格的方可进行数控开料机的操作。
First of all, the operator must be very familiar with the CNC cutting machine, whether it is to say that the structure of the cutting machine, the scope of application, or the technical specifications of the cutting machine and the safety rules that must be observed when using, they must be familiar with the heart, so as to avoid accidents in use. In addition, before the formal operation, the operator is generally required to take an examination. Only those who pass the examination can operate the CNC cutting machine.
双工序开料机一旦进行操作，就非常容易发生意外，对机器以及设备操作者都造成非常---的损伤，所以必须要引起各部门的高度重视。
Once the double process cutting machine is operated, it is very easy to cause accidents, which will cause great damage to the machine and equipment operators. Therefore, it is necessary to attach great importance to it by all departments.

双工序开料机用久了也会出现这样那样的毛病，下面就跟小编一起来看看该如何保养双工序开料机生产设备吧：
The double process cutting machine will also have such and other problems after a long time of use. Let's take a look at how to maintain the production equipment of the double process cutting machine with the help of small knitting machine
一、连续运行时间每天10小时以下，冷却水的清洁及水泵的正常工作，绝不可使水主轴电机出现缺水现象，定时更换冷却水，以防止水温过高。冬季如果工作环境温度太低可把水箱里面的水换成防冻液。
1、 The continuous operation time is less than 10 hours per day. The cleaning of cooling water and the normal operation of the water pump can never cause water shortage of the water spindle motor. Replace the cooling water regularly to prevent the water temperature from being too high. In winter, if the working environment temperature is too low, the water in the water tank can be replaced with antifreeze.
二、每次机器使用完毕，要注意清理，务必将平台及传动系统上的粉尘清理干净，定期(每周)对传动系统(x、y、z三轴)润滑加油。(注：x、y、z三轴光杆用机油进行保养;丝杆部分加高速黄油;冬季如果工作环境全自动电脑雕刻机温度太低丝杆、光杆(方形导轨或圆形导轨)部分应先用汽油进行冲洗清洁，然后加入机油，否则会造成机器传动部分阻力过大而导致机器错位。)
2、 Every time the machine is used, attention should be paid to cleaning. The dust on the platform and transmission system must be cleaned, and the transmission system (x, y, Z three axes) should be lubricated regularly (weekly). (Note: X, y, Z three-axis polished rod is maintained with oil; high-speed grease is added to the screw rod; in winter, if the temperature of the full-automatic computer engraving machine is too low, the screw rod and polished rod (square guide rail or circular guide rail) should be washed and cleaned with gasoline first, and then oil should be added. Otherwise, the resistance of transmission part of the machine will be too high and the machine will be misplaced. )
双工序开料机
Double process cutting machine
三、对电器进行保
3、 Protect electrical appliances
养检查是，一定要切断电源，待---无显示及主回路电源指示灯熄灭后，电脑木工雕刻机可进行。
Maintenance inspection is, must cut off the power supply, until --- no display and the main circuit power indicator light off, computer woodworking engraving machine can be carried out.
四、长期不使用本机时，应把各部分擦拭干净，并用塑料或篷布覆盖防尘。
4、 When the machine is not used for a long time, all parts should be wiped clean and covered with plastic or tarpaulin to prevent dust.