联系我们
18560023440
王经理：18560023440
地址：山东省德州市齐河县经济开发区齐众大道7号-2车间
业内资讯
导致石材雕刻机出现错位表象的原因是什么？
来源：http://www.jmycnc.com 时间：2020-12-04
石材雕刻机在雕刻过程中出现各种错位缺点，如左右错位、上下错位、x轴错位、z轴错位等等，终究是什么缘由致使雕刻机出现错位表象呢?
Stone engraving machine in the process of carving a variety of dislocation defects, such as left and right dislocation, up and down dislocation, X-axis dislocation, z-axis dislocation and so on. What causes the carving machine to appear dislocation appearance?
1.检查雕刻软件的途径正确与否；
1. Check whether the way of engraving software is correct or not;
2.检查丝杆的空地巨细及光杆的紧固螺丝有没有松动；
2. Check the space size of the screw rod and whether the fastening screw of the polished rod is loose;
3.检查软件参数的设置正确与否；
3. Check whether the software parameters are set correctly;
4.检查地线是不是接好；
4. Check whether the ground wire is well connected;
5.电脑是不是有病毒或许与其他不兼容或许烦扰，一般主张无须企业机简略拼装机箱即可；
5. Whether the computer has virus or not, it may be incompatible with other computers or annoyed. Generally speaking, it is not necessary to simply assemble the chassis of brand-name computers;
6.水冷主轴电机前上方的联轴器，是不是松动损坏，可检查用手拧紧或许替换；
6. If the coupling at the top and front of the water-cooled spindle motor is loose and damaged, it can be checked and replaced by hand;
7.雕刻机横梁上到机器控制箱联接拖链的线，是不是有接触不良；
7. Whether there is poor contact between the line connecting the crossbeam of engraving machine and the drag chain of machine control box;
8.驱动器的疑问：驱动器本身里面的布局或许电子原器材有疑问，也会构成错位表象，这个缘由比较多，若出现的次数不多，而且把速度下降一点，有时能正常雕刻，这说明驱动器还没有彻底坏掉；若是一开始雕刻就错位，就说明驱动器彻底坏了。处理方法：修补驱动器或许替换驱动器；
8. Questions about the driver: the layout of the drive itself may have doubts about the original electronic equipment, which may also constitute the appearance of dislocation. This is due to a lot of reasons. If the number of times is not too many, and the speed is reduced a little, sometimes it can carve normally, which indicates that the driver has not been completely damaged; if the engraving is misplaced at the beginning, the driver is completely broken. Treatment: repair the drive or replace the drive;
9.电压的疑问：雕刻机在作业时需求的功率大，若是电压过低，给驱动器供电缺少，功率达不到则会构成错位表象，这种情况一般以Y轴错位为多，出现这种表象有可能是外界电压不可，或许在同一线路上有人使用了大功率的设备如电焊等。处理方法：装置一个5000瓦的稳压电源，但这个稳压电源的过失规划不能超过5%，建议在3%以内；
9. Question of voltage: the engraving machine needs high power during operation. If the voltage is too low, the power supply to the driver is insufficient, and the power can not reach it, it will form a dislocation image. In this case, Y-axis dislocation is more common. This appearance may be caused by external voltage. Maybe someone has used high-power equipment such as welding on the same line. Treatment method: install a 5000 Watt regulated power supply, but the fault planning of this regulated power supply should not exceed 5%, and it is recommended to be within 3%;
10.接口板，主板，转接板的疑问：要是接口板，主板，转接板坏了，雕刻机在作业的过程中，某一个方向或许是三个轴均不动，构成雕刻错位；
10. Interface board, motherboard, adapter board questions: if the interface board, motherboard, adapter board are broken, engraving machine in the process of operation, a certain direction may be three axes are not moving, constitute carving dislocation;
主轴电机的疑问：要是步进电机或许是伺服电机的疑问，整个机器在某一方向上都不移动，用手转丝杆也转不动。
Spindle motor question: if the stepper motor may be a servo motor, the whole machine does not move in a certain direction, and the screw rod can not rotate by hand.
11.机床本身的疑问：机床上的某个部件有疑问或许是松动，表面有杂质等也会出现错位表象;如联轴器松了，坏了，都会出现错位;导轨，丝杆上长期没有清洁加油也会出现错位表象；机床线要是断了也会出现错位表象。
11. Problems of the machine tool itself: some parts on the machine tool may be loose, and there are impurities on the surface. If the coupling is loose or broken, there will be dislocation; if the guide rail and screw rod have not been cleaned and oiled for a long time, the dislocation image will also appear; if the machine tool line is broken, it will also appear dislocation appearance.
- 上一篇：四工序开料机的主轴电机冷却方式？
- 下一篇：石材雕刻机怎么选用质量好的石材
