联系我们
18560023440
王经理：18560023440
地址：山东省德州市齐河县经济开发区齐众大道7号-2车间
新闻资讯
保丽龙雕刻机常见的问题的解决方法
来源：http://www.jmycnc.com 时间：2020-10-26
保丽龙雕刻机在日复一日的工作过程中难免会出现一些问题，有些原因是因为机器本身配置的问题，有些原因则是由于客户误操作造成，下面墨源就一些常见的问题做了一些整理，以供大家参考：
In the process of working day after day, some problems will inevitably appear in the process of polylon engraving machine, some of which are caused by the configuration of the machine itself, and some of the reasons are caused by the wrong operation of customers. The following ink source has done some sorting on some common problems for your reference:
一：保丽龙雕刻机工作过程中主轴电机突然停转或转慢。
1： The spindle motor suddenly stops or slows down during the working process of styrofoam engraving machine.
原因：
reason:
1、 工作电压不稳或超负载，加个稳压器即可。
1. Working voltage instability or overload, add a voltage regulator can.
2、 检查中间线是否接好，线头是否有脱焊。
2. Check whether the middle line is well connected and whether the wire end is desoldered.
墨源数控采用的装配工艺，每台出厂的机器都经过72小时高强度的质检测试，确保机器0故障，同时及时的售后服务团队也一时间帮助客户解决机器使用过程中出现的故障，确保客户的是生产精度不受影响。
Ink source CNC adopts advanced assembly technology, each machine has passed 72 hours of high-intensity quality inspection test to ensure that the machine has no fault. At the same time, the timely after-sales service team also helps customers solve the problems in the process of using the machine, so as to ensure that the production accuracy of customers is not affected.
二：保丽龙雕刻机不能在原点雕刻。
2： The styrofoam engraving machine can't carve at the origin.
原因：
reason:
1、 文件的版面大小是否与机器匹配。
1. Whether the layout size of the file matches the machine.
2、 检查是否设有偏移量（OFFSET），版面设置是否正确。
2. Check whether offset is set and the layout is set correctly.
三：保丽龙雕刻机启动复位时发出异常声响或总是顶坏限位开关
3： Baolilong engraving machine makes abnormal sound when it starts to reset or always breaks the limit switch
原因：
reason:
1、顶不到限位开关，把其较正即可。
1. If it can not reach the limit switch, just align it.
2、驱动线接触不好，驱动线固定即可。
2. If the drive line is not in good contact, the drive line can be fixed.
3、限位开关线没接好，把线接好即可。
3. If the limit switch wire is not connected well, just connect it.
4、限位开关损坏，换之即可。
4. If the limit switch is damaged, replace it.
四：保丽龙雕刻机设置原点时有时向前偏移或向右偏移且偏移距离不定。
4： Styrofoam engraving machine set the origin sometimes forward or right offset and the offset distance is uncertain.
原因：
reason:
1、 限位开关失灵，在系统回到系统原点的过程中限位开关已闭合又弹开。换限位开关即可。
1. The limit switch fails. In the process of the system returning to the system origin, the limit switch has been closed and opened. Replace the limit switch.
2、 驱动线松动。设法把其固定紧即可。
2. The drive line is loose. Try to fix it tightly.
通过小编本文的讲解，希望可以帮助到您，如需更多的精彩内容请关注公司网站：http://www.jmycnc.com
Through the explanation of this article, I hope it can help you. If you need more wonderful content, please pay attention to the company's website: http://www.jmycnc.com
- 上一篇：保丽龙雕刻机的操作拥有哪些功能？
- 下一篇：五轴保丽龙雕刻机与四轴保丽龙雕刻机的区别
