With the wide application of stone engraving machine, more and more customers who have just begun to understand CNC stone carving machine often ask: "how about the carving speed and how long does it take to carve a square meter"?

雕刻的速度有很多种因素，不可置否的是机器本身的配置，整理的功率。还有就是技术的熟练的掌握程度，刀具的选择，石材的材质等等详细分解如下：

There are many factors in the speed of engraving. First of all, it is the configuration of the machine itself and the power of finishing. In addition, the mastery of technology, the selection of cutting tools, and the material of stone materials are detailed as follows:

石材雕刻机

Stone carving machine

1、理论基础：培训工作必须从理论培训工作开始，操作人员必须在理论考核通过的情况下方可进行实际操作培训。若理论培训没有通过，则坚决不能进行操作培训。

1. Theoretical basis: the training work must start from the theoretical training, and the operators must pass the theoretical assessment before they can carry out practical operation training. If the theoretical training is not passed, the operation training can not be carried out.

2、石材雕刻机刀具的使用问题：在理论培训以后，必须进行刀具的培训。操作人员能对常见刀具、雕刻电机转速、行进速度、注意事项等，必须清楚，操作人员必须熟悉刀具的应用。

2. Stone engraving machine tool use problem: after the theoretical training, must carry on the tool training. The operator must be clear about the common tools, engraving motor speed, travel speed, precautions, etc., and the operator must be familiar with the application of the tool.

3、石料的应用范围：操作人员必须熟悉各种材料的应用范围，熟悉不同的材质，不同的厚度、不同的成品大小等。熟悉不同的材料的不同雕刻方式。

3. Application scope of stone: operators must be familiar with the application range of various materials, different materials, different thickness, different size of finished products, etc. Be familiar with different carving methods of different materials.

4、石材雕刻机各种软件的操作：在通过以上培训后方可进行软件培训。软件的培训主要集中在用户应用的领域;软件的要求为：软件的各种排版、各种的操作、路径的生成、能迅速找出路径的错误等。

4. All kinds of software operation of stone carving machine: software training can be carried out after the above training. The training of software is mainly focused on the field of user application; the requirements of software are: various typesetting, various operations, path generation, and the ability to quickly find path errors.

一、连续运行时间每天10小时以下，保证冷却水的清洁及水泵的正常工作，绝不可使水主轴电机出现缺水现象，定时更换冷却水，以防止水温过高。冬季如果工作环境温度太低可把水箱里面的水换成防冻液。

1、 The continuous operation time is less than 10 hours a day to ensure the cleaning of cooling water and the normal operation of the water pump. Never make the water spindle motor lack of water. Replace the cooling water regularly to prevent the water temperature from being too high. In winter, if the working environment temperature is too low, the water in the water tank can be replaced with antifreeze.

二、每次机器使用完毕，要注意清理，务必将平台及传动系统上的粉尘清理干净，定期(每周)对传动系统(X、Y、Z三轴)润滑加油。(注：X、Y、Z三轴光杆用机油进行保养；丝杆部分加高速黄油；冬季如果工作环境全自动电脑雕刻机温度太低丝杆、光杆(方形导轨或圆形导轨)部分应先用汽油进行冲洗清洁，然后加入机油，否则会造成机器传动部分阻力过大而导致机器错位。)

2、 Every time the machine is used, attention should be paid to cleaning. The dust on the platform and transmission system must be cleaned, and the transmission system (x, y, Z three axes) should be lubricated regularly (weekly). (Note: X, y, Z three-axis polished rod is maintained with oil; screw rod is added with high-speed grease; in winter, if the temperature of full-automatic computer engraving machine is too low, the screw rod and polished rod (square guide rail or circular guide rail) shall be washed with gasoline first, and then oil shall be added, otherwise, the resistance of transmission part of the machine will be too high, resulting in machine dislocation. )

三、对电器进行保

3、 Protect electrical appliances

养检查是，一定要切断电源，待监视器无显示及主回路电源指示灯熄灭后，电脑木工雕刻机可进行。

Maintenance inspection is, must cut off the power supply, until the monitor has no display and the main circuit power indicator light is off, the computer woodworking engraving machine can be carried out.

以上就是小编分享的全部内容了，大家如果还有其他想要了解的，可以通过下面的联系方式，咨询厂家，厂家会给您详细介绍产品内容。

The above is the small editor to share all the content, if you have other want to know, you can contact the following, consult the manufacturer, the manufacturer will give you a detailed description of the product content.