联系我们
18560023440
王经理：18560023440
地址：山东省德州市齐河县经济开发区齐众大道7号-2车间
新闻资讯
激光雕刻机激光头安装后的注意事项！
来源：http://www.jmycnc.com 时间：2020-03-02
如果是用激光雕刻机还是移动后的位置，注意检查高压电缆是否断开，以防触电。
If using laser engraving machine or moving position, pay attention to check whether the high-voltage cable is disconnected to prevent electric shock.
【激光雕刻机】安装激光头后注意事项
[laser engraving machine] precautions after installation of laser head
1. 如果使用激光雕刻机一次或移动位置，请注意检查高压电缆是否脱落，以免触电。
1. If the laser engraving machine is used once or moved, please pay attention to check whether the high-voltage cable falls off to avoid electric shock.
激光雕刻机应防止强烈的震动，移动时应先固定好小车和小车，以免震动引起光路偏差或激光裂纹。
The laser engraving machine shall be protected from strong vibration. When moving, the trolley and trolley shall be fixed first to avoid the optical path deviation or laser crack caused by vibration.
3、注意防止冷却水结冰，北方天气寒冷时应特别注意冬季更好更换汽车防冻液，温度过高，有结垢或污垢堵塞机械冲击等原因造成激光损伤。
3. Pay attention to prevent the cooling water from freezing. When the weather is cold in the north, it is better to change the automobile antifreeze in winter. If the temperature is too high, the laser damage will be caused by scaling or dirt blocking mechanical impact.
激光雕刻机内部电压高，非技术人员不应打开机壳进行维修，以防触电。
The internal voltage of laser engraving machine is high. Non professional technicians should not open the shell for maintenance to prevent electric shock.
激光雕刻机应水平放置在桌面上，不能倾斜。
The laser engraving machine shall be placed horizontally on the table top and shall not tilt.
6. 确保使用过程中冷却水循环良好，水质清洁。如果水是脏的和黄色的，及时更换水，避免激光管冷却不良和爆炸。
6. Ensure that the cooling water circulation is good and the water quality is clean during use. If the water is dirty and yellow, change the water in time to avoid poor cooling and explosion of the laser tube.
7、注意防止底盘内部部件因过度冒烟和潮湿而腐蚀损坏。所以每次清洗完工件后要保持机器的卫生，保持机器的清洁，要做经常性的擦拭。
7. Take care to prevent corrosion damage to internal parts of the chassis due to excessive smoke and moisture. So every time after cleaning the workpiece, keep the machine clean, keep the machine clean, and wipe it regularly.
8、激光雕刻机工作时必须严格防止工作人员或其他人员用手或用眼睛来观察，万一激光损伤或损伤到眼睛，更好是将盖子扣死。
8. When the laser engraving machine is working, it must be strictly prevented that the workers or other personnel use their hands or eyes to observe. In case of laser damage or eye damage, it is better to buckle the cover.
9. 请避免水进入设备或工作环境太潮湿。保持机器在干燥和通风的地方。
9. Please prevent water from entering the equipment or working environment. Keep the machine in a dry and ventilated place.
10. 严禁拆卸各类接插件。
10. It is strictly prohibited to dismantle all kinds of connectors.
11、雕刻机内的镜片应及时用无水乙醇或丙酮清洗，并轻轻擦拭放好，擦拭时调整光路。
11. The lens in the engraving machine shall be cleaned in time with anhydrous alcohol or acetone, and placed gently, and the light path shall be adjusted when wiping.
以上都是为您介绍的内容，希望对您有所帮助。如果您想了解更多的知识，可以访问我们的网站，我们将为您提供更的信息。
All of the above are for you, I hope to help you. If you want to know more, you can visit our website and we will provide you with more professional information.
- 上一篇：木工油气润滑和油雾润滑的不同点！
- 下一篇：五轴加工有哪几种?
