联系我们
18560023440
王经理：18560023440
地址：山东省德州市齐河县经济开发区齐众大道7号-2车间
业内资讯
木工加工指标！
来源：http://www.jmycnc.com 时间：2019-04-23
购买了木工加工的客户，在使用过程中应该要注意使用，因为机械设备都具有很强的危险性，平时使用应该要做好防护措施，因为不挡使用机器造成的伤害屡见不鲜，下面罗列一些木工加工指标供参考。
Customers who have purchased woodworking processing centers should pay attention to the use safety in the process of use, because the machinery and equipment are very dangerous. They should take good protective measures when using them in peacetime, because the damage caused by using the machines is not uncommon. Here are some safety indicators of woodworking processing centers for reference.
1、购买木工加工时要按照有轮必有罩、有轴必有套和锯片有罩锯，条有套，刨（剪）、切有挡，器送料的要求，对各种木工机械配置相应的防护装置，尤其徒手操作接触危险部位的，应该要有防护措施。
1. When purchasing a woodworking processing center, it is necessary to configure corresponding safety protection devices for various woodworking machinery, especially for bare-handed operation in contact with dangerous parts, in accordance with the requirements of wheels, shafts and saw blades with hood saws, strips with sleeves, planers (shears), cutters with blockades, and feeding safety devices.
2、对生产噪声、木粉尘或挥发性有害气体的木工加工，要配置与其机械运转相连接的消声、吸尘或通风装置，以保证工人的和健康。
2. For woodworking processing centers that produce noise, wood dust or volatile harmful gases, noise-attenuating, dust-absorbing or ventilating devices connected with their mechanical operation should be equipped to ensure the safety and health of workers.
3、木工加工的刀轴与电气应有联控装置，在装卸或更换刀具及维修时，能切断电源并保持断开位置，以防误触电源开关或突然供电启动机械而造成人身伤害事故。
3. The cutter shaft and electrical equipment of woodworking processing center should have safety joint control device. When loading, unloading or replacing cutters and repairing, the power supply can be cut off and the disconnection position can be maintained in order to prevent personal injury caused by mistakenly touching the power switch or suddenly starting the machine with power supply.
4、针对木材加工作业中的木料反弹危险，应采用送料装置或设置分离刀、防反弹屏护装置，以保障人身。
4. In view of the rebound danger of wood in wood processing, safety feeding device or separation knife and anti-rebound safety screen device should be adopted to ensure personal safety.
5、在装设正常启动和停机操纵装置的同时，还应专门设置遇事故需紧急停机的控制装置。
5. While installing normal start-up and shutdown control devices, special safety control devices for emergency shutdown in case of accidents should also be set up.
6、经常检查线路，保证不漏电、接好地线。
6. Check the line regularly to ensure no leakage and good connection.
以上内容由济南木工加工整理发布，更多相关信息可以点击我们的官网进行咨询：http://www.yijuncnc.com
The above content is organized and published by Jinan Woodworking Processing Center. More relevant information can be consulted by clicking on our official website: http://www.yijuncnc.com.
- 上一篇：
- 下一篇：木工加工和木工雕刻机有什么区别？
