保丽龙雕刻机不能正常工作时，一般是由以下原因造成的，操作者可以根据实际情况来判断和解决。

When the styrofoam engraving machine can not work normally, it is generally caused by the following reasons, the operator can judge and solve according to the actual situation.

(1)保丽龙雕刻机三轴中有一轴不能动，此时要检查一下相应全顺保丽龙雕刻机轴所对应的驱动块是否损坏。检查方法可使用替换法：将全顺保丽龙雕刻机不动轴所对应的航空插头拔下插在其他能动轴所对应的驱动上。

(1) One of the three axes of the styrofoam engraving machine is not active. At this time, it is necessary to check whether the drive block corresponding to the axis of the styrofoam engraving machine is damaged. The inspection method can be replaced: pull out the aviation plug corresponding to the fixed shaft of Quanshun styrofoam engraving machine and plug it into the corresponding drive of other active shafts.

保丽龙雕刻机

(2)保丽龙雕刻机如果交换后不动轴走动正常，则可说明该轴所对应的驱动块已损坏，需要更换好驱动块。如果不动轴还是不行就说明电缆线或电机有故障更换电缆线或者电机。三轴均不能动。此时检查一下三轴航空插头是否已和控制箱连接好，控制箱电源是否已打开。数据线是否和控制箱和电脑主机中控制卡连接好。如果以上都正常，则请和全顺保丽龙雕刻机授权维修点联系。

(2) If the fixed shaft moves normally after exchanging, it indicates that the drive block corresponding to the shaft is damaged and needs to be replaced. If the shaft still does not move, it means that the cable or motor is faulty, replace the cable or motor. All three axes can't move. At this time, check whether the three-axis aviation plug has been connected with the control box, and whether the power supply of the control box has been turned on. Whether the data line is well connected with the control card in the control box and computer host. If the above is normal, please contact Quanshun Baolilong engraving machine authorized maintenance point.

(3)保丽龙雕刻机主轴不能正常运转。检查变频器LED显示屏显示的错误代码(参见全顺保丽龙雕刻机变频器说明书错误代码项)

(3) The main shaft of styrofoam engraving machine can not work normally. First, check the error code displayed on the inverter LED display screen (refer to the error code item in the frequency converter Manual of Quanshun Baolilong engraving machine)

主轴电机全顺保丽龙雕刻机常见故障和处理：

Common faults and treatment of main shaft motor Quanshun Baolilong engraving machine:

保丽龙雕刻机电机发烫检查水泵是否工作循环水是否正常，电机没劲检查电机线是否缺相电缆是否短路，电机声音异常电机是否超负荷运转电机内部故障，电机反转检查电机线是否缺相将输出UVW端任意调换两端。

The motor of styrofoam engraving machine is hot, check whether the water pump works, whether the circulating water is normal, whether the motor is weak, whether the motor line is short circuited, whether the motor sound is abnormal, whether the motor is overloaded, whether the internal fault of the motor, the motor reverses to check whether the motor line is lack of phase, and the output UVW end will be randomly exchanged at both ends.