济南雕刻机在运行中要注意正确的方法

来源：http://www.jmycnc.com 时间：2021-06-21 

济南雕刻机的使用率在逐年提高，甚遍及各个行业和领域，但也有因为发展迅速，设备操作中的一些细节问题往往被忽略，导致一些人在运行中出现各种问题。那么，大家知道设备在运用中要注意哪些方法和技巧吗?下面墨源数控就为您介绍下具体的内容。

The utilization rate of Jinan engraving machine is increasing year by year, even throughout various industries and fields. However, due to the rapid development, some details of equipment operation are often ignored, leading to various problems in the operation of some people. So, do you know what methods and skills should be paid attention to in the use of equipment? The following ink source CNC will introduce the specific content for you.

1、使用之前检查电机主轴冷却中冷却液的储存量，开启电机的主轴冷却，保证冷却液循环正常。开启正压密封，以避免加工废液、冷却液等进入电机主轴轴承。

1. Before use, check the coolant storage in the motor spindle cooling, turn on the motor spindle cooling, and ensure that the coolant circulation is normal. Open the positive pressure seal to prevent the processing waste liquid and coolant from entering the motor spindle bearing.

2、在雕刻过程中，切记带上手套清理雕刻碎片，或触摸雕刻主轴，主轴高速运转，很容易在手套和手一起滚动，带来隐患;

2. In the carving process, remember to wear gloves to clean up the carving debris, or touch the carving spindle, the spindle runs at high speed, it is easy to roll together in gloves and hands, which brings hidden danger;

3、使用济南雕刻机雕刻时，在装卸雕刻板时，须先卸下雕刻工具，以免锋利的工具对操作者造成伤害。

3. When using Jinan engraving machine to carve, when loading and unloading the engraving board, the engraving tools must be removed first to avoid the sharp tools causing damage to the operator.

4、雕刻机的操作看似简单，但也有很多操作要求和规范需要注意，上岗前须经过严格的培训和考核，以免操作中出现失误带来麻烦。

4. The operation of engraving machine seems simple, but there are also many operation requirements and specifications need to be paid attention to. Before taking up the post, we must go through strict training and assessment, so as to avoid the trouble caused by mistakes in operation.

5、济南雕刻机在使用过程中，不得随意操作。如有故障，应先切断电源，再进行维修，以免高速雕刻机对操作人员造成伤害;

5. Jinan engraving machine is not allowed to operate at will during use. If there is any fault, the power should be cut off first, and then the maintenance should be carried out, so as to avoid the injury of the high-speed engraving machine to the operators;

6、雕刻过程中，严禁近距离观察，以防切屑飞入眼睛。观察时要暂停雕刻，关闭电机主轴并确定电机主轴不再旋转。雕刻过程中，严禁用手摸切削表面，禁止使用棉丝擦拭工作表面。

6. In the process of carving, close observation is strictly prohibited to prevent chips from flying into the eyes. Pause engraving during observation, close the motor spindle and make sure that the motor spindle does not rotate any more. In the process of carving, it is forbidden to touch the cutting surface with hands and wipe the working surface with cotton thread.

7、雕刻前要认真检查所使用刀具的尺寸，性能是否满足加工编程要求。

7. Before carving, carefully check the size and performance of the cutting tools to meet the requirements of machining programming.

8、每天下班前10分钟，对机床加油润滑及擦洗清洁机床。确认机床停止运转，将机床停在指定位置，关闭电源，确认所有开关己断开，方可离开。

8. Lubricate and clean the machine tool 10 minutes before work every day. Confirm that the machine tool stops running, stop the machine tool at the designated position, turn off the power, and confirm that all switches have been disconnected before leaving.

建议用户在使用济南雕刻机进行工作之前，要有一定的经验技术，参加过技术培训，以免操作中因为操作不当、不熟练等问题，导致设备出现故障或者给人身健康带来伤害。不清楚方法的用户可以参考上述内容进行使用，以便雕刻机能充分发挥其作用。

It is suggested that users should have certain technical experience and participate in technical training before using Jinan engraving machine, so as to avoid equipment failure or personal health injury due to improper operation and unskilled operation. Users who are not clear about the method can refer to the above content for use, so that the engraving function can give full play to its role.

• 上一篇：雕刻机的干扰问题怎么解决？
• 下一篇：木工雕刻机故障如何预防？

相关产品：
• 
  木工雕刻机
• 
  1325木工雕刻机独...
• 
  1325木工雕刻机
• 
  1325木工镂空花格...
• 
  1225型平雕圆雕一...

相关新闻：
• 
  激光雕刻机和机械雕刻...
• 
  三轴雕刻机无心外圆磨...
• 
  石材雕刻机断刀的原...
• 
  数控开料机会受到什么...
• 
  泡沫雕刻机日常井盖如...