联系我们
18560023440
王经理：18560023440
地址：山东省德州市齐河县经济开发区齐众大道7号-2车间
新闻资讯
使用五轴泡沫雕刻机时维修保养和注意事项
来源：http://www.jmycnc.com 时间：2020-10-15
1.发动前查验五轴雕刻机各处摇杆是不是在正常部位，各运动部件是否完好无损，滑轨有机油润化，随后发动底速动转1~2分钟，观查是不是有异常现象，等数控车床运转正常后方能进行作业。
1. Before starting, first check whether the rocker of the five axis engraving machine is in the normal position, whether the moving parts are intact, and whether the slide rail is lubricated with oil. Then, start the machine at the bottom speed for 1-2 minutes to observe whether there is any abnormal phenomenon. The operation can be carried out after the CNC lathe runs normally.
2.泡沫雕刻机主轴轴承、操作台和滑轨面制止敲击和冲击，操作台及钢轨面不可乱堆专用工具和毛胚及不相关的钢件或物件。
2. the main bearings, operation tables and slide surfaces of foam engraving machines should be used to stop percussion and impact. Special tools and hairs and unrelated steel parts or objects should not be huddle on the operation platform and rail surface.
3.有效切削，调节适合的变大（变小）倍率，视出产加工情况选择数控刀片、转速比、下刀量、出产加工速率及顺，逆铣方位。
3. Effective cutting, adjust the suitable increasing (decreasing) ratio, and select CNC blade, speed ratio, cutting amount, production processing rate and the direction of forward and backward milling according to the production and processing conditions.
4.悉数出产过程中，不能戴手套，关于出产过程中有木渣飞溅时要做好双眼的保护作业，出产过程中不可以用力或碎布条等脏物触碰现已旋转的数控刀片，在铲除木渣时要确保数控刀片完全终止运转才可以木渣。
4. Do not wear gloves in the production process. When there is wood residue splashing in the production process, protect your eyes. Do not use force or rags to touch the rotary NC blade. When removing the wood residue, ensure that the NC blade completely stops running to eliminate the wood residue.
5.作业完毕，断电，铲除各方位木渣，脏物。其他相关辅助工具必须放还原处。
5. After operation, cut off the power and remove the wood slag and dirt in all directions. Other related auxiliary tools must be placed in the restoration place.
6.作业台面及滑轨每日擦洗干净，不能有木渣、油渍残渣等。
6. The worktable and slide rail shall be cleaned daily, and there shall be no wood residue, oil residue, etc.
7.接连运作时间每天10钟头以下，确保冷却循环水的清理及离心水泵的正常作业，决不能够 使水冷散热伺服电机出現少水情况，定时执行拆换冷却循环水，以避免温度过高。储水箱里边的冷却循环水每日必须拆换一次；
7. The continuous operation time is less than 10 hours per day, to ensure the cleaning of cooling circulating water and the normal operation of centrifugal pump, and never make the water cooling servo motor lack of water. Regularly replace the cooling circulating water to avoid excessive temperature. The cooling circulating water inside the water storage tank must be removed and replaced once a day;
8.五轴泡沫雕刻机每一次设备运用完毕，要留心铲除，尽量将服务平台及传动装置上的烟尘铲除干净，准时（每星期）对传动装置（X,Y,Z三轴）润化加油。滑轨可运用油枪上油，滚珠丝杆要加0﹟润滑油脂或无盐黄油；
8. the five axis foam engraving machine should be carefully removed after every equipment is used. Try to clean up the smoke and dust on the service platform and the transmission device, and run the oil on the X (Y, Z three axis) on time (every week). The slide rail can be oiled with oil gun, and the ball screw should be added with 0 lubricating grease or salt free grease;
9.设备若长时间不运用，应准时（每星期）加油空走，以确保传动装置的和谐能力。
9. If the equipment is not used for a long time, it should be filled with oil and left empty on time (every week) to ensure the harmonious ability of the transmission device.
10.准时（依运用情况）铲除电器箱里尘土，查验接线端子排螺钉是不是松脱，以确保设备电源电路性，靠谱运用；
10. Remove the dust in the electrical box on time (according to the application situation), and check whether the screw of the terminal block is loose, so as to ensure the safety of the power supply circuit of the equipment and reliable application;
11.准时（依运用情况）查验设备各构件螺丝是不是松脱，以确保设备靠谱运转。
11. Check whether the screw of each component of the equipment is loose or not on time (according to the application situation) to ensure the reliable operation of the equipment.
12.对电器进行保护保养查验时，一定要断开开关电源，待监控器无显示信息及主操控回路指示灯吹灭后，即可进行。
12. When checking the protection and maintenance of electrical appliances, it is necessary to disconnect the switching power supply. After the monitor has no display information and the indicator light of the main control circuit blows out, it can be carried out.
标签：五轴保丽龙雕刻机
- 上一篇：一台五轴保丽龙雕刻机？
- 下一篇：教你应如何选择合适自己的石材雕刻机？
