欢迎光临山东墨源数控设备有限公司官网为您提供:保丽龙雕刻机,五轴保丽龙刻机,四轴保丽龙雕刻机

NEWSCENTER
新闻资讯
联系我们

18560023440

王经理:18560023440
地址:山东省德州市齐河县经济开发区齐众大道7号-2车间

新闻资讯 当前位置:首页 - 新闻中心 > 新闻资讯

数控开料机如何合理保养提高家具生产效率

来源:http://www.jmycnc.com 时间:2022-01-14 

1、开机前,先检查设备的线路是否完好,电压是否稳定,确认无误后才能开机,待机空置一段时间后再开始加工。
1. Before starting up, check whether the circuit of the equipment is intact and whether the voltage is stable. Start up after confirming that there is no error. Wait for a period of time and then start processing.
2、数控开料机主轴有两种类型,一种是风冷主轴,另一种是水冷主轴,冷却轴需要清洗和冷却才能正常工作,在此提醒大家:水冷主轴不能缺水。
2. There are two types of spindles of CNC cutting machine, one is air-cooled spindle and the other is water-cooled spindle. The cooling shaft needs cleaning and cooling to work normally. Here we remind you that the water-cooled spindle cannot be short of water.
3、除了以上保养工作外,还要注意水温,冷却水温度过高会使冷却效果大大下降,对主轴造成一定的损坏,因此需要及时更换冷却水。冬天还要采取防冻措施,防止冻裂水管。
3. In addition to the above maintenance work, pay attention to the water temperature. Too high cooling water temperature will greatly reduce the cooling effect and cause certain damage to the main shaft. Therefore, the cooling water needs to be replaced in time. Antifreeze measures should also be taken in winter to prevent frost cracking of water pipes.
对数控开料机电路箱的散热性和通风系统进行定时清扫,检查各风扇是否工作正常,对电气控制箱内灰尘进行定时清扫,检查接线端子螺钉松动,确保电路使用可靠。
Regularly clean the heat dissipation and ventilation system of the circuit box of the NC opener, check whether each fan works normally, regularly clean the dust in the electrical control box, and check the looseness of the connecting terminal screws to ensure the reliable use of the circuit.
及时清理导轨及周围的木屑,及时给设备的驱动系统加料。
Clean the wood chips on the guide rail and around in time, and feed the driving system of the equipment in time.
6、将感应器上的灰尘、油污及时除干净。
6. Remove the dust and oil stain on the sensor in time.
7、在数控开料机上开料后,取出刀片,使主轴夹头处于放松状态。有利于延长主轴座的使用寿命。
7. After cutting on the NC cutting machine, take out the blade to make the spindle chuck in a relaxed state. It is beneficial to prolong the service life of the spindle seat.
下一步我们开始清理台面,可用毛刷清理桌面,注意一般台面尽量不要杂物堆积,以免台面变形。割断电源前,应将机头移到左下或右下位置,避免碰撞。
Next, we start to clean the table. We can clean the table with a brush. Note that the general table should not accumulate sundries as far as possible to avoid deformation of the table. Before cutting off the power supply, move the machine head to the lower left or right position to avoid collision.
8、长时间不使用数控开料机时,尽量每周通电一次,防止机器受潮,保证设备的电气元件性能稳定可靠。
8. When the numerical control cutting machine is not used for a long time, try to power on once a week to prevent the machine from moisture and ensure the stable and reliable performance of the electrical components of the equipment.
9、数控开料机如经常打开橱柜,通常在打开橱柜时空气中会有灰尘、木屑或金属粉尘,一旦掉进电控箱的电路板或电子设备上,就容易造成元件之间的绝缘电阻降低,甚损坏元件及电路板。
9. If the NC cutting machine often opens the cabinet, there will be dust, sawdust or metal dust in the air when opening the cabinet. Once it falls into the circuit board or electronic equipment of the electric control box, it is easy to reduce the insulation resistance between components and even damage components and circuit boards.
本文的精彩内容由四工序开料机为您提供,本网站还有很多的精彩内容,更多的内容您可以点击进入:http://www.jmycnc.com/我们有专门的客服为您解答问题
The wonderful content of this article is provided by the four process cutting machine. There are many wonderful content on this website. You can click to enter more content: http://www.jmycnc.com/ We have special customer service to answer your questions