First of all, the operator must be very familiar with the CNC cutting machine, whether it is the structure of the cutting machine, the scope of application, or the technical specifications of the cutting machine, as well as the safety rules that must be observed when using, they must be familiar with the heart, so as to avoid accidents when using. In addition, before the formal operation, the operator is generally required to take an examination. Only those who pass the examination can operate the CNC cutting machine.

数控开料机一旦进行操作，就非常容易发生意外，对机器以及设备操作者都造成非常---的损伤，所以必须要引起各部门的高度重视。

Once the CNC cutting machine is operated, it is very easy to have accidents, which will cause great damage to the machine and equipment operators, so it must be paid attention to by all departments.

橱柜门板生产设备用久了也会出现这样那样的毛病，下面就跟小编一起来看看该如何保养橱柜门板生产设备吧：

The cabinet door panel production equipment will also have such and such problems after long use. Let's take a look at how to maintain the cabinet door panel production equipment with Xiaobian

一、连续运行时间每天10小时以下，冷却水的清洁及水泵的正常工作，绝不可使水主轴电机出现缺水现象，定时更换冷却水，以防止水温过高。冬季如果工作环境温度太低可把水箱里面的水换成防冻液。

1、 The continuous operation time is less than 10 hours per day. The cleaning of the cooling water and the normal operation of the water pump must not make the water spindle motor short of water. The cooling water should be replaced regularly to prevent the water temperature from being too high. If the working environment temperature is too low in winter, the water in the water tank can be changed into antifreeze.

二、每次机器使用完毕，要注意清理，务必将平台及传动系统上的粉尘清理干净，定期(每周)对传动系统(x、y、z三轴)润滑加油。(注：x、y、z三轴光杆用机油进行保养;丝杆部分加高速黄油;冬季如果工作环境全自动电脑雕刻机温度太低丝杆、光杆(方形导轨或圆形导轨)部分应先用汽油进行冲洗清洁，然后加入机油，否则会造成机器传动部分阻力过大而导致机器错位。)

2、 Every time the machine is used, pay attention to cleaning, be sure to clean up the dust on the platform and transmission system, and lubricate the transmission system (x, y, z axes) regularly (weekly). (Note: the X, y, Z three-axis polished rod is maintained with engine oil; the screw rod part is added with high-speed grease; if the temperature of the fully automatic computer engraving machine is too low in winter, the screw rod and polished rod (square or circular guide rail) part should be washed with gasoline first, and then added with engine oil, otherwise the resistance of the machine transmission part will be too large and the machine will be misplaced. )

三、对电器进行保

3、 Protect electrical appliances

养检查是，一定要切断电源，待---无显示及主回路电源指示灯熄灭后，电脑木工雕刻机可进行。

Maintenance inspection is, be sure to cut off the power supply, until --- no display and main circuit power indicator light off, computer woodworking engraving machine can be carried out.

四、长期不使用本机时，应把各部分擦拭干净，并用塑料或篷布覆盖防尘。

4、 When the machine is not used for a long time, all parts should be wiped clean and covered with plastic or tarpaulin to prevent dust.

以上就是橱柜门板生产设备的保养方法建议希望能给大家能带来帮助，橱柜门板生产设备在企业生产运营中是站着非常重要的位置，一旦机器出现了故障也会延迟了生产工期，所以机器的保养和维护是非常重要的。

The above is the maintenance method of cabinet door production equipment. I hope it can help you. Cabinet door production equipment is very important in the production and operation of enterprises. Once the machine fails, it will delay the production period, so the maintenance and maintenance of the machine is very important.